rsg electronic components gmbh ?sprendlinger ldst. 115 ? 63069 offenbach ?+49 69-984047-0 ?rsg-electronic.de page 1 (4) stand juni 2016 rev 01 1) these are stress ratngs. exposure of devices to any of these conditons may adversely afect long-term reliability. 2) (1.5mm from case 10sec max.) 3) all specifcatons typical at ta= 25c, nominal input voltage and full load unless otherwise specifed. 4) the informaton and specifcaton contained in this data sheet are believed to be correct at tme of publicaton. however rsg accepts no responsibility for consequences arising from printng errors or inaccuracies. specifcatons are subject to change without notce. dc/dc-converter rr7-s05/d05 5.0w 4:1 regulated single & dual output we energize electronics! an acal group company we energize electronics! ? 24 pin dil package ? wide 4:1 input range ? 1500vdc isolaton ? up to 3500vdc isolaton ? contnuous short circuit protecton ? efciency up to 84% ? operatng temperature range -40 ~ +85c ? metal case standard , optonal plastc case ? emi complies with en55022 class a output specification voltage accuracy: 1% line regulaton: single &dual 0.5% max. load regulation: 0.5% output 3.3v model: 1.5% short circuit protecton : indefnite (automatc recovery) ripple noise (20mhz bandwidth): 60mv pk-pk temperature coefcient: 0.02% c capacitor load: see table input specifications voltage range: see table max. input current: see table no-load/full-load input current: see table input filter: pi type input refected ripple current : 35ma pk-pk general specifications efciency: see table typ. i/o isolaton voltage metal case (3 sec.): 1000vdc i/o isolaton voltage (3 sec.): 1500 ~ 3500vdc i/o isolaton capacitance: 500pf typ. i/o isolaton resistance: 1000m ohm switching frequency: 266khz, typ. humidity: 95% rel h reliability calculated mtbf : > 1.21mhrs (mil-hdbk-217 f) safety standard: (designed to meet): iec 60950-1 environmental specification operatng temperature range: -40c ~+85c (see deratng curve) maximum case temperature: 100c storage temperature : -40c ~+125c cooling : nature convecton physical specifications: case material: nickel-coated copper base material: non-conductve black plastc (ul94v-0 rated) pin material: ? 0.5mm brass solder coated potng material: epoxy (ul94v-0 rated) weight case-dip: 17.0g ( metal), 13.5g (plastc) dimmension dip: 1.25 x 0.8 x 0.4 absolute maximum ratings (1) input surge voltage (100ms)/ 24v models: 40vdc max. 48v models: 80vdc max. soldering temperature: 260c max. (2) emc specifications radiated-/conducted emissions: en55022 class a esd: iec 61000-4-2 perf.criteria a rs: iec 61000-4-3 perf.criteria a eft: iec 61000-4-4 perf.criteria a surge: iec 61000-4-5 perf.criteria a cs: iec 61000-4-6 perf.criteria a pfmf iec 61000-4-8 perf.criteria a rohs
rsg electronic components gmbh ?sprendlinger ldst. 115 ? 63069 offenbach ?+49 69-984047-0 ?rsg-electronic.de page 2 (4) stand juni 2016 rev 01 r r 7 - xx xx s/d xx power (w) input t ype a x x code inter nal isolation (kvdc) model selection guide model number input voltage range (vdc) input current output voltage (vdc) output current efficiency @fl(%) capacitor load(uf) no - load (ma) full load (ma) min. load (ma) full load ( m a ) rr7 - 2403s05ax 9 - 36 18 238.3 3 . 3 13 75 1 7 2455 9 3 18 2.4 5 1 8 8 7 2475 9 3 18 2.4 7 . 2 94 8 47 7 2495 9 3 18 257.2 9 0 555 81 220 rr7 - 2412s05ax 9 - 36 18 254.1 12 41 82 1 7 24155 9 3 18 251 15 0 333 83 100 rr7 - 2418s05ax 9 - 36 18 260.4 18 0 277 80 68 rr7 - 2424s05ax 9 - 36 18 260.4 24 28 8 47 7 2435 9 3 18 281.5 3.3 0 5 7.2 0 347 80 100 rr7 - 2409d05ax 9 - 36 18 257.2 9 12 15 18 0 138 80 22 rr7 - 2424d05ax 9 - 36 18 260.4 24 0 104 80 22 rr7 - 4803s05ax 18- 72 15 119.2 3 . 3 13 75 1 7 4855 18 72 15 13.2 5 1 8 8 7 4875 18 72 15 13.2 7 . 2 94 8 47 7 4895 18 72 15 128. 9 555 81 22 7 48125 18 72 15 124 12 0 416 84 100 rr7 - 4815s05ax 18 - 72 15 125.5 15 333 83 1 7 48185 18 72 15 13.2 18 0 277 80 68 rr7 - 4824s05ax 18- 72 15 130.2 24 28 8 47 7 4835 18 72 15 14.7 3.3 5 0 500 80 330 rr7 - 4807d05ax 18- 72 15 130.2 7.2 347 80 100 rr7 - 4809d05ax 18 - 72 15 128.6 9 0 12 0 208 83 47 rr7 - 4815d05ax 18- 72 15 125.5 15 0 166 83 47 rr7 - 4818d05ax 18- 72 15 130.2 18 0 138 80 22 rr7 - 4824d05ax 18- 72 15 130.2 24 104 80 22 suffix ? 3 ? means 3.5kvdc isolation suffix ?p? means plastic case instead of standard metal case the models listed above is just for standard type. if you need the special specification product, please contact our service member by telephone presented in shortform cover or e - mail t o : info@rsg - electronic.de dc/dc-converter -/d ete ne d tt we energize electronics! an acal group company we energize electronics!
rsg electronic components gmbh ?sprendlinger ldst. 115 ? 63069 offenbach ?+49 69-984047-0 ?rsg-electronic.de page 3 (4) stand juni 2016 rev 01 output ripple & noise measurement test copper strip +vout use a capacitor cout(1.0uf) measurement. the scope measurement bandwidth is 0 - 20mhz. single dc/dc converter 1uf cout resistive scope load - vout input reflected ripple current test step +vout input reflected ripple current is measured through a source inductor lin(12uh) and a source capacitor cin(47uf, esr<1.0? at 100khz) at nominal input and full load. +vin lin current probe cin dc/dc converter load - vin - vout emi filter +vout +v i n l input filter components (c1,c2, l) are used to help meet conducted emissions requirement for the module. these components should be mounted as close as possible to the module; and all leads should be minimized to decrease radiated noise. dc/dc converter loa d c1 c2 - vin - vout c1 l c2 68uf, 100v 12uh 33uf, 100v 1. ripple/noise measured with a 1uf ceramic capacitor. 2. test by nominal input voltage and constant resistor load. 3. measured input reflected ripple current with a simulated source inductance of 12uh. 4. it?s recommended to add (c1, c2, l) in input end to achieve en55022 conducted class a. 5. an external filter capacitor is required if the module has to meet iec61000 - 4 - 5. the filter capacitor rsg suggest: nippon - chemi - con ky series, 220uf/100v. 6. exceeding the absolute ratings of the unit could cause damage. it is not allowed for continuous operating. efficiency vs output current 90 85 80 75 70 65 60 55 50 lo line nominal hi line 0% 20% 40% 60% load 80% 100% 120% efficiency vs output current 90 85 80 75 70 65 60 55 50 lo line nominal hi line 0% 20% 40% 60% load 80% 100% 120% 2 4 model s 4 8 model s efficiency(%) efficiency(%) output ripple & noise measurement test copper strip +vout use a capacitor cout(1.0uf) measurement. the scope measurement bandwidth is 0 - 20mhz. single dc/dc converter 1uf cout resistive scope load - vout input reflected ripple current test step +vout input reflected ripple current is measured through a source inductor lin(12uh) and a source capacitor cin(47uf, esr<1.0? at 100khz) at nominal input and full load. +vin lin current probe cin dc/dc converter load - vin - vout emi filter +vout +v i n l input filter components (c1,c2, l) are used to help meet conducted emissions requirement for the module. these components should be mounted as close as possible to the module; and all leads should be minimized to decrease radiated noise. dc/dc converter loa d c1 c2 - vin - vout c1 l c2 68uf, 100v 12uh 33uf, 100v 1. ripple/noise measured with a 1uf ceramic capacitor. 2. test by nominal input voltage and constant resistor load. 3. measured input reflected ripple current with a simulated source inductance of 12uh. 4. it?s recommended to add (c1, c2, l) in input end to achieve en55022 conducted class a. 5. an external filter capacitor is required if the module has to meet iec61000 - 4 - 5. the filter capacitor rsg suggest: nippon - chemi - con ky series, 220uf/100v. 6. exceeding the absolute ratings of the unit could cause damage. it is not allowed for continuous operating. efficiency vs output current 90 85 80 75 70 65 60 55 50 lo line nominal hi line 0% 20% 40% 60% load 80% 100% 120% efficiency vs output current 90 85 80 75 70 65 60 55 50 lo line nominal hi line 0% 20% 40% 60% load 80% 100% 120% 2 4 model s 4 8 model s efficiency(%) efficiency(%) output ripple & noise measurement test copper strip +vout use a capacitor cout(1.0uf) measurement. the scope measurement bandwidth is 0 - 20mhz. single dc/dc converter 1uf cout resistive scope load - vout input reflected ripple current test step +vout input reflected ripple current is measured through a source inductor lin(12uh) and a source capacitor cin(47uf, esr<1.0? at 100khz) at nominal input and full load. +vin lin current probe cin dc/dc converter load - vin - vout emi filter +vout +v i n l input filter components (c1,c2, l) are used to help meet conducted emissions requirement for the module. these components should be mounted as close as possible to the module; and all leads should be minimized to decrease radiated noise. dc/dc converter loa d c1 c2 - vin - vout c1 l c2 68uf, 100v 12uh 33uf, 100v 1. ripple/noise measured with a 1uf ceramic capacitor. 2. test by nominal input voltage and constant resistor load. 3. measured input reflected ripple current with a simulated source inductance of 12uh. 4. it?s recommended to add (c1, c2, l) in input end to achieve en55022 conducted class a. 5. an external filter capacitor is required if the module has to meet iec61000 - 4 - 5. the filter capacitor rsg suggest: nippon - chemi - con ky series, 220uf/100v. 6. exceeding the absolute ratings of the unit could cause damage. it is not allowed for continuous operating. efficiency vs output current 90 85 80 75 70 65 60 55 50 lo line nominal hi line 0% 20% 40% 60% load 80% 100% 120% efficiency vs output current 90 85 80 75 70 65 60 55 50 lo line nominal hi line 0% 20% 40% 60% load 80% 100% 120% 2 4 model s 4 8 model s efficiency(%) efficiency(%) dc/dc-converter rr7-s05/d05 5.0w 4:1 regulated single & dual output we energize electronics! an acal group company we energize electronics!
rsg electronic components gmbh ?sprendlinger ldst. 115 ? 63069 offenbach ?+49 69-984047-0 ?rsg-electronic.de page 4 (4) stand juni 2016 rev 01 rr7-xxxxs02a1 31.75 (1.25) 20.32 (0.80) 0.50 (0.02) 5.08 (0.20) 15.24 (0.60) 10.16 (0.40) 3.00 (0.12) 0.50 (0.02) 22.86 (0.9) printed face 2 3 1 1 9 3 2 2 2 14 bottom v iew 16 24 pin dil package non-conductive plastic dc-dc conver ter xxxx pin connections pin number 2 3 1 1 9 1 4 1 6 2 2 2 3 single v input v input v input v input + v output +v output n.p. common n.c. v output v output common + v input + v input + v input + v input dual for ?p? case the pin connection of high isolation one is the same with normal one. pin connections pin number 2 3 1 1 9 1 4 1 6 2 2 2 3 single v input v input v input v input v output +v output n.p. common n.c. v output + v output common + v input + v input + v input + v input dual 24 pin dil package nickel-coated copper bottom view 3 1 . 7 5 ( 1 . 25) 2 0 . 3 2 ( 0 . 8 ) 2 2 . 8 6 ( 0 . 9 ) 2 . 5 4 ( 0 . 1 0 ) dia 0 . 5 0 ( 0 . 02) 1 5 . 2 4 ( 0 . 6 0 ) printed face 1 0 . 1 6 ( 0 . 4 0 ) 3 . 0 0 ( 0 . 1 2 ) built - in stand - o s help air convection dc-dc convert er xxxx 2 3 1 1 16 14 23 22 9 notes: all dimensions are typical in millimeters ( inches ). 1. pin diameter: 0.5 0.05 ( 0.02 0.002 ) 2. pin pitch and length tolerance: 0.35 ( 0.014 ) 3. case tolerance: 0.5 ( 0.02 ) notes: all dimensions are typical in millimeters ( inches ). 1. pin diameter: 0.5 0.05 ( 0.02 0.002 ) 2. pin pitch and length tolerance: 0.35 ( 0.014 ) 3. case tolerance: 0.5 ( 0.02 ) the pin connection of high isolation one is the same with normal one. mecchanical specifica tions rr7-xxxxs05a1 rr7-xxxxs05a1p dc/dc-converter rr7-s05/d05 5.0w 4:1 regulated single & dual output e enegie electonic an acal goup copan e enegie electonic mechanical specifications the models listed here are just standard type. if you need a product with special specifcaton or you have questons regarding packing standards (tube oder tape/reel) as well as applicaton support, please contact our specialists: sales @ rsg-electronic.de or +49 69-984047-41/-28
|
